How many gallons of water are in 1600 cubic feet?
How many gallons of water are in 1600 cubic feet?
Convert 1,600 Cubic Feet to Gallons
| cu ft | gal |
|---|---|
| 1,600 | 11,969 |
| 1,610 | 12,044 |
| 1,620 | 12,118 |
| 1,630 | 12,193 |
How many gallons are in a foot of pipe?
Volume and Weight of Water for Common Pipe Sizes
| Pipe Size | Volume | |
|---|---|---|
| in | in3/ft | gallons/ft |
| 1/2“ | 2.356 in3 | 0.0102 gal |
| 3/4“ | 5.301 in3 | 0.0229 gal |
| 1″ | 9.425 in3 | 0.0408 gal |
How many gallons per minute will flow through a 1-inch pipe?
210 gallons
How many gallons of water are in 100 feet of 1-inch pipe?
4 gallons
How much water is in a 2 inch pipe?
Estimate water content in pipes – weight and volume
| Pipe Size (inside diameter) (in) | Water Content | |
|---|---|---|
| Volume | ||
| 2 | 37.7 | 0.163 |
| 2 1/2 | 58.9 | 0.255 |
| 3 | 84.8 | 0.367 |
How many cups of water are you supposed to drink a day?
The U.S. National Academies of Sciences, Engineering, and Medicine determined that an adequate daily fluid intake is: About 15.5 cups (3.7 liters) of fluids a day for men. About 11.5 cups (2.7 liters) of fluids a day for women.
Can you lose weight by drinking a gallon of water a day?
A third benefit to drinking a gallon of water each day is that water consumption helps curb hunger cravings, and without as much appetite for snacks or second helpings, you might even see some weight loss.
How do you calculate flow rate with pressure?
With a radius, for instance, of 0.05 meters, 0.05 ^ 2 = 0.0025. Multiply this answer by the pressure drop across the pipe, measured in pascals. With a pressure drop, for instance, of 80,000 pascals, 0.0025 x 80,000 = 200. Multiply the constant pi by the answer to Step 1: 3.142 x 0.0025 = 0.00785.
How do you calculate the drop factor?
To calculate the drops per minute, the drop factor is needed. The formula for calculating the IV flow rate (drip rate) is total volume (in mL) divided by time (in min), multiplied by the drop factor (in gtts/mL), which equals the IV flow rate in gtts/min.
What is the standard drop factor?
In general, standard (macrodrip) administration sets have a drip factor of 10, 12, 15, or 20 gtt/ml (drops per milliliter). For a microdrip (minidrip) set, it’s 60 gtt/ml.
What is a drop factor?
Drop factor = the number of drops it takes to make up one ml of fluid. Two common sizes are: 20 drops per ml (typically for clear fluids) 15 drops per ml (typically for thicker substances, such as blood)
What is the formula for drug calculation?
A basic formula, solving for x, guides us in the setting up of an equation: D/H x Q = x, or Desired dose (amount) = ordered Dose amount/amount on Hand x Quantity.
What is Young’s rule formula?
A rule for calculating the dose of medicine correct for a child by adding 12 to the child’s age, dividing the sum by the child’s age, then dividing the adult dose by the figure obtained.
What percentage is 5 mg per mL?
Answer: First convert 1% solution to mg/cc. A 1% solution is the same as 1000 milligrams in 100 cc or 10mg/cc. Percent solutions all are 1000mg/100cc. For example a 2% = 20mg/cc, 5% = 50mg/cc, 5.5% = 55mg/cc, etc……
| CONCENTRATION | DOSAGE EQUIVALENCE | PERCENT |
|---|---|---|
| 1:200,000 | 0.005mg/mL | 0.0005% |
What is the formula of volume strength?
The volume of hydrogen peroxide used = 100 ml. Hence, the volume strength of H2O2 is 56. Additional information: We can relate the volume strength of hydrogen peroxide with its molarity. According, to the equation, 1 L of H2O2 will produce a V volume of oxygen gas.
What is the volume strength of 1.5 h2 O2?
Hence, volume strength of 1.5NH2O2=8.4 volume.
What is the strength of 10 volume solution of hydrogen peroxide?
So, 10 litres of Oxygen at STP is produced from 68×1022.4=30.36≈30gH2O2. Therefore, strength of H2O2in 10 volume H2O2 solution is 30g per litre i.e. 3H2O2 solution.
What is the strength of 20 volume solution of h2 O2?
6g/litre.
What is the strength of 20 volume h2 O2 in terms of g per Litre?
6gL−1.